ANALISIS KENYAMANAN PENGEMBANGAN PRODUK MEJA SETRIKA MENGGUNAKAN RAPID UPPER LIMB ASSESSMENT (RULA)
DOI:
https://doi.org/10.31949/jensitec.v11i01.11924Abstract
The development of the ironing table product that is currently made only uses the same design, there is no difference in terms of shape or form and there are not many additional functions. This study aims to identify the size of the ironing table with anthropometry, create a design for developing an ironing table and product development after being folded into a chair, and measure the comfort of product development with a product reference using Rapid Upper Limb Assessment (RULA). In this study, anthropometry was used to determine the size of the product to be made, and Rapid Upper Limb Assessment (RULA) was used to identify and compare the comfort between reference products and products being developed. The results of the introduction of the ironing table product size using anthropometry are the height of the ironing table of 105 cm, the height and width of the ironing table of 50 cm, the length of the ironing table of 120 cm, the height of the chair seat of 40 cm, the width of the chair seat of 60 cm, the length of the chair seat of 50 cm, and the height of the chair backrest as high as 125 cm. Based on the results of the comfort analysis using RULA, it can be seen that the development product has a smaller value compared to the reference product, so the conclusion is that overall the development product is more comfortable to use than the reference product.
Keywords:
Ironing table, anthropometry, RULADownloads
References
C. I. Erliana and K. Amri, "Analisis Postur kerja Menggunakan Metode Rapid Upper Limb Assesment (RULA) pada Proses Pembuatan Plat Sambung Tiang Pancang PT. WIjaya Karya Beton, TBK Binjai," Industrial Engineering Journal, vol. 9, no. 1, 2020.
A. N. Pramana, B. Kurniawan and Ekawati, "Analisis Postur Kerja Dengan Menggunakan Metode Rapid Upper Limb Assessment (Rula) pada Pekerja di Laundry X Kota Semarang," Indonesian Journal of Health Community, vol. 2, no. 2, pp. 57-66, 2021.
M. Fauzan, I. A. Fathulloh, D. B. Daniswara and A. M. Suyono, "Analisis Pengukuran Postur kerja dalam Proses Menyetrika Baju Menggunakan Metode RULA di CV. Hijrah Laundry," Scientica : Jurnal Ilmiah Sains dan Teknologi, vol. 2, no. 9, pp. 18-24, 2024.
A. U. Azmi, "Desain Ulang Alat Setrika Baju Dengan Metode RULA dan OWAS untuk Mengurangi Risiko Cedera Operator," Universitas Brawijaya, 2018.
S. Namwongsa, R. Puntumetakul, M. S. Neubert, S. Chaiklieng and R. Boucaut, "Ergonomic Risk Assessment of Smartphone Users Using The Rapid Upper Limb Assessment (RULA) tool," PLoS ONE, vol. 13, no. 8, pp. 1-16, 2018.
A. A. R. Putri, R. A. Ratriwardhani, M. Sunaryo and M. N. Rhomadhoni, "Analisis Postur Kerja Dengan Metode Rapid Upper Limb Assessment (RULA) dan Nordic Body Map pada Pekerja Produksi di PT. Jayamas Medica Industri Kab. Sidoarjo," Jurnal Ilmiah Wahana Pendidikan, vol. 8, no. 13, pp. 1-11, 2022.
N. Miswari, L. Aulia and R. Wahyudi, "Penilaian Postur Kerja Manual Material Handling (MMH) pada Gedung Bertingkat Menggunakan Metode Rapid Upper Limb Assessment (RULA)," Sebatik, vol. 25, no. 1, pp. 262-270, 2021.
Whydiantoro, D. Susandi, H. Rastiawan and I. Kusumadewi, "Analisis Postur Kerja Manual Material Handling (MMH) Menggunakan Rapid Upper Limb Assessment (RULA) di PT. XYZ," J-ENSITEC : Journal of Engineering and Sustainable Technology, vol. 8, no. 1, pp. 592-298, 2021.
L. D. Murti, "Pemilihan Konsep Produk Meja Setrika Menggunakan Metode Matriks Pugh," Universitas Gunadarma, Jakarta, 2021.
Y. Kurnia and E. Aristriyana, "Perancangan Kursi kerja Pada Stasiun Pengupasan Pisang Menggunakan Metode Antropometri di IKM Keripik Pisang CIpaku - Ciamis," J-ENSISTEC (Journal of Engineering and Sustainable Technology), vol. 10, no. 1, pp. 961-966, 2023.
A. N. Bintang and S. K. Dewi, "Analisa Postur Kerja Menggunakan Metode OWAS dan RULA," Jurnal Teknik Industri, vol. 18, no. 01, pp. 43-54, 2017.
N. Dzikrillah and E. N. S. Yuliani, "Analisis Postur Kerja Menggunakan Metode Rapid Upper Limb Assessment (RULA) Studi Kasus PT. TJ Forge Indonesia," Jurnal Ilmiah Teknik Industri, vol. 3, no. 3, pp. 150-155, 2015.
Published
How to Cite
Issue
Section
License
Copyright (c) 2024 Ina Siti Hasanah, Septa Adi Nugroho
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
An author who publishes in the J-ENSITEC (Journal of Engineering and Sustainable Technology) agrees to the following terms:
- Author retains the copyright and grants the journal the right of first publication of the work simultaneously licensed under the Creative Commons Attribution-ShareAlike 4.0 License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal
- The author is able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book) with the acknowledgment of its initial publication in this journal.
- The author is permitted and encouraged to post his/her work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of the published work
